Ultra Start KE-6 Guía de instalación descargar pdf (Pagina 10)

Installation Guide

Setting 1- Method 2- Low Idle Learn

Setting 1- Method 1- Auto Tach Learn

Setting 2- Adjust For Over-Crank

Setting 3- Adjust For Under-Crank

1) - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button 1 time.

2) - Enter Program Menu 4 - Press the # button on the remote transmitter.(Button #4).

3) - Start Vehicle - Using the key, make sure not to turn the key. Do not turn key off then start.

4) - Press the Program Button - One time (The LED’s on the will start flashing in single cycles)

5) - Press And Hold - The Program Button for five seconds or until the horn (Optional) honks once.

6) - Release Button - The LED’s will turn on solid if a proper Tach is detected.

1) - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) press the Program button one time.

2) - Enter Program Menu 4 - Press the # button on the remote transmitter.(Button #4).

3) - Press the Program Button - Two times (The LED’s on will start flashing in cycles of two)

4) - Press And Hold - The Program Button for five seconds or until the horn (Optional) honks once.

5) - Release Button - And exit program mode. Test the remote starter and adjust again if needed*.

* Try changing to a different tach source if adjustment is not successful.

Note: Each time the park lights flash (Horn honks) the tach is decreased by 10%. Continue to hold the

program button to reduce the Tach by multiple percentages.

1) - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.

2) - Enter Program Menu 4 - Press the # button on the remote transmitter.(Button #4).

3) - Press the Program Button - Three times (The LED’s on the antenna will start flashing in cycles of three)

4) - Press And Hold - The Program Button for five seconds or until the horn (Optional) honks once.

5) - Release Button - Exit program mode. Test the remote starter a number of times and adjust again if needed*.

* Try changing to a different tach source if adjustment is not successful.

Note: Each time the park lights flash (Horn honks) the tach is increased by 10%. Continue to hold the program button

to reduce the Tach by multiple percentages.

This option is used for vehicles that maintain a HIGH or erratic idle after starting and

need more that 30 seconds to establish a stale idle.

Menu 4 - Tach Settings

Menu 5 - Auxiliary Output Settings

1 Ground On Start 1 Flash Ground output During crank ( Bulb test/ Caravan 2nd Starter...)

2 Park Light (Negative) 2 Flashes Negative output upon park light activation

3 Re-arm 3 Flashes See starter settings options, Setting 3

Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flash and one park light flash)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release. Press the Program button momentarily to move to next program step or repeat to change selection.

1 Dome Light Supervision 1 Flash 30 second output on unlock

2 Second Lock Output 2 Flashes Press Unlock twice within 3 seconds ( Window Roll-up...)

3 Disarm 3 Flashes .75 Second pulse on Unlock and start

Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes and 2 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release. Press the Program button momentarily to move to next program step or repeat to change selection.

1 Dome Light Supervision 1 Flash 30 second output on unlock

2 Second Lock Output 2 Flashes Press Unlock twice within 3 seconds ( Window Roll-up...)

3 Trunk Release 3 Flashes Output for .75 seconds or until the button is released

Press the Program Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes and 3 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release. Press the Program button momentarily to move to next program step or repeat to change selection.

1 Park Light (Negative) 1 Flash Negative output upon park light activation

2 Dome Light Supervision(Button 5) 2 Flashes 30 second output on unlock

3 Latched Output (Button 5) 3 Flashes Activated on first button press, deactivates on second press.

4 60 Second Output(Button 5) 4 Flashes Output will activate for 60 seconds when button 5 is pressed.

5 Momentary Output (Button 5) 5 Flashes Output will activate for .75 seconds when button 5 is pressed

Press the Program Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes and 4 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release. Press the Program button momentarily to move to next program step or repeat to change selection.

Setting 1 - Output 1 - Yellow wire on the 14-pin connector

New Auxiliary Output Menu.

Setting 2 - Output 2 - Brown wire on the 14-pin connector

Setting 3 - Output 3 - Red/White wire on the 14-pin connector

Setting 4 - Output 4 - Orange wire 0n the 14-pin connector

Setting 5 - Output 5 - Yellow wire on the 2-pin white connector

1) Plug in the module, the park lights will flash and the horn will honk two times.*

*If the lights do not flash check connections. Ign must be off when plugged-in.

2) Turn the Ignition Key to the ON position. (The Park Lights will turn on).

3) Start the vehicle with the ignition key, The LED’s on antenna will come on solid when

proper tach signal is detected*. The Tach Learning process will take up to 36 seconds.

When the system has learned the Tach signal the park lights flash and the horn

(Optional) will honk twice to confirm Tach Learning**.

Note: The system will flash the park lights seven times if not Tach Learned and

the start button is pressed. Must be tach learned before remote starting.

* If the LED’s do not turn on or flash erratically, A proper tach signal was not detected.

** If the park lights do not flash in auto tach learn mode it may be necessary to connect

to a different tach source. Connect the tach wire to the coil pack or fuel injector wire*.

****The Tach wire must be above 2 Volts A/C for proper detection.

Note: Setting 6 in the Starter Settings menu must be programmed for option 2 (Auxiliary Output) before this menu will

operate as an Auxiliary output.

The auxiliary output menu allows the installer to choose the output on a desired wire

from the main unit. This option will allow for such things as custom remote features,

additional remote starter accessories and button configurations.

1 Momentary Output (Button 6) 1 Flash Output will activate for .75 seconds when button 5 is pressed

2 60 Second Output (Button 6) 2 Flashes Output will activate for 60 seconds when button 5 is pressed.

3 Latched Output (Button 6) 3 Flashes Activated on first button press, deactivates on second press. (Button 5)

4 Ground On Start 4 Flashes Ground output During crank ( Bulb test/ Caravan 2nd Starter...)

5 Park Light (Negative) 5 Flashes Negative output upon park light activation

Press the Program Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes and 5 horn honks)

Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or horn honks.

Release. Press the Program button momentarily to move to next program step or repeat to change selection.

Enter menu 5 By pressing button 5, located to the left of the buttons.

# &

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Ultra Start KE-6 Guía de instalación Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para La electrónica del vehículo de motor Ultra Start KE-6