Ultra Start KE-6 Guía de instalación descargar pdf (Pagina 6)

Installation Guide

Yellow Starter Output Connect To The Vehicles Starter Wire.

Green Heater Output Connect To The Vehicles Accessory Wire.

Red 12 power Input Connect to Constant 12 Volt Power Source

Blue Ignition 1 Output Connect To the Vehicles Primary Ignition.

6 Pin Power Connector

14 Pin Power Connector

Manual Transmissions Only

Step 2- Plug-In The Module

Step 3- Auto Tach Learn

Your Basic Install Is Complete!

Step 1 - The Following Wires Must Be Connected!

Black System Ground Connect To Chassis Ground.

Pink Brake Switch Connect To (+) When Brakes Applied.

White Park Lights Connect To (+) Park Light System.

Green/White Hood Pin Connect To Hood Pin Switch.

Blue/White Tach Input Connect To A/C Tach Source.

Violet (+) Door Input Connect this wire to negative door pin switches.

Green (-) Door Input Connect this wire to positive door pin switches.

Black/White Park Brake Connect this wire to the vehicles park brake wire.

NOTE: Manual Transmissions MUST be set into RESERVATION MODE!

1) Plug in the module. (See above)

**The park lights should flash twice upon power up.

2) Turn the Ignition Key to the ON position. (The Park Lights will turn on).

3) Start the vehicle with the ignition key, The LED’s on antenna will come on solid when

proper tach signal is detected*. The Tach Learning process will take up to 36 seconds.

When the system has learned the Tach the park lights flash and the horn (Optional) will

honk twice to confirm Tach Learning**.

Note: The system will flash the park lights seven times if not Tach Learned and the

start button is pressed. The system must be tach learned before remote starting.

* If the LED’s do not turn on or flash erratically, A proper tach signal was not detected.

** If the park lights do not flash in auto tach learn mode it may be necessary to connect to

a different tach source. For best results connect the tach wire to the coil pack or to a fuel

injector wire*.

***The ignition 1 input Must be connected to a wire that does Not turn off in the Start

position.

*The Tach wire must be above 2 Volts A/C for proper detection.

***To relearn a tach signal the system must first be reset to defaults. See page 7.***

Make all wiring connections before connecting the module. The ignition must be in the

OFF position. Plug in the 6 pin connector followed by the 14-pin connector then any

other connectors that were used. When the system is powered up the system will

respond by flashing the park lights and honking the horn (Optional) twice. If this does not

happen, disconnect the module and check that the system has a good ground and that

the ignition wire has no voltage present.

Program mode allows you to adjust the settings and options of your system. The system’s default

settings do not require any program changes in most cases. However, this system does incorporate

a highly advanced programming system that includes 5 menus with numerous options and settings

that can be easily adjusted for custom installations.

User Settings - Page 8.

This menu contains settings that adjust the way the system operates for the user.

Additional Settings - Page 8.

This menu contains additions settings

Starter Settings - Page 9

This menu controls features and settings associated with remote car starter applications.

Tach Settings - Page 10

This menu allows the programming and adjustment of the Tach Signal

Auxiliary Output - Page 11

This menu contain the settings for the Auxiliary Outputs of the system.

Programming Overview

Entering Program Mode

Changing the Programmable Settings

To Enter Program Mode

1) Make sure ignition is in the off position.

2) Within three seconds turn the key ON - OFF - ON - OFF - ON. Leave “ON”

3) Press and release the Program Button on the antenna 1 time.

4) Park lights will come on and the horn will honk to confirm entering program mode.

5) Select Desired Program Menu by the following:

Press Button #1 Lock User Options See Page 8.

Press Button #2 Unlock Additional Settings See Page 8.

Press Button #3 Start Remote Start Options See Page 9

Press Button #4 # Tach Adjustment Menu See Page 10.

Press Button #5 Aux Advanced Auxiliary Control See Page 11.

6) The selected mode will be confirmed by a horn honk and one park light flash.

7) The program menu may be changed at any time by pressing the transmitter buttons

as above, this allows the installer to change a setting from one menu, then move to

Another menu and change another setting without re-entering the Program Mode.

8) Turning off the ignition or 30 seconds of no activity will exit the Program Mode.

To Select and Change A Program Setting:

1) Enter Program Mode.

2) Select the desired Program Menu. (See pages 8 through 11.)

3) Press & release the Program Button the correct number of times to select the desired

Program Setting(as listed on pages 8 through 11.) The park lights will flash and the horn

(optional) will honk to indicate the current setting that is selected.

4) Press and hold the Program Button until the parking lights / horn confirm the selected setting.

The park lights will flash and the horn will honk to indicate the option selected within the setting.

SYSTEM RESET

Quick Start Installation

Programming Introduction

1) - Within 3 seconds turn the ignition key ON-OFF-ON-OFF-ON (Leaving the Key ON).

2) - Press and release the Program Button.

3) - The park lights will come ON

4) - Quickly press and hold the Program Button a second time for 8 Seconds. The park lights will

Flash and the horn (Option) will honk three times.

The System Is Now Re-Set To Factory Defaults.

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Comentarios a estos manuales

Sin comentarios

Ultra Start KE-6 Guía de instalación Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para La electrónica del vehículo de motor Ultra Start KE-6