Ultra Start KE-6 Guía de instalación descargar pdf (Pagina 15)

Installation Guide

ULTRA

Press Once to Lock Doors and arm alarm (if equipped)

Press 2nd Time & Hold for Constant Lock Output

Press Once to Lock Doors and arm alarm (if equipped)

Press 2nd Time & Hold for Constant Lock Output

Press Once for Unlock doors and Disarm Alarm (if equipped)

Press & Hold for Trunk / Aux Output

Press Once for Unlock doors and Disarm Alarm (if equipped)

Press & Hold for Trunk / Aux Output

Press Once for Start - (2 Times if programmed for safety start)

Press & Hold for 3 seconds while running to turn off

Press Once for Start - (2 Times if programmed for safety start)

Press & Hold for 3 seconds while running to turn off

Press once and hold for Car Finder

Press & Release then press START and hold for Timer Mode

2nd Car Operation

Battery Replacement

Step 1 - Within three seconds turn the Key ON-OFF-ON-OFF-ON - Leaving Key ON

Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if park-

lights do not come on at this point, turn key off for 5 seconds, the repeat step 1.

Step 3 - Continue to hold the Program Switch until park lights go out.

Step 4 - Press the LOCK button on each of 1st car remote’s and press the # button on

each of the 2nd car remote’s of the transmitters to be programmed. The park lights

will flash once and the horn will honk once each time a new code is learned.

Note: Transmitter programming must done quickly. Do not pause more than one

second between each transmitter. All the transmitters to be used must be

programmed at the same time. All transmitters not programmed at this time will

be erased from memory for security. The system holds a maximum of 4

transmitter codes including 2nd car remote codes.

You can program the same remote as a 1st car remote in one vehicle and as a 2nd car

remote in a second vehicle.

Carefully remove the

screw from back of the

remote.

Remove top case

then replace the

battery.

Replace top

case.

Test remote for

proper operation.

The transmitter battery should be changed at least once every year to maintain proper operating range.

Replace with quality23A 12volt Alkaline battery.

Transmitter Programming

First Car

2nd Car

then

Activating Service Mode

1. While the ignition is in the “ON” position, press and hold the Program Button

located on the antenna for five seconds. The park lights will flash five times and

the horn (optional)will honk five times to confirm that the system is in Service

Mode.

* The LED’s on the antenna will be “ON” solid when in Service Mode.

Deactivating Service Mode

1. While the ignition is the “ON” position, press and hold the Program Button located

on the antenna for five seconds. The park lights will flash two times and the horn

(optional)will honk two times to confirm that the system has exited Service

Mode.

* The LED’s will turn off and the system will return to normal operation.

Activating Service Mode

1. Press and release button #4 then within 2 second press and hold the same

button for 8 seconds. The park lights will flash five times and the horn

(optional)will honk five times to confirm that the system is in Service Mode.

* The LED’s on the antenna will be “ON” solid when in Service Mode.

Deactivating Service Mode

1. Press and release button #4 then within 2 second press and hold the same button

for 8 seconds. The park lights will flash five times and the horn (optional)will honk

five times to confirm that the system is in Service Mode.

*The LED’s will turn off and the system will return to normal operation.

System Service Mode (Valet Mode)

System Service Mode (Valet Mode) - By Remote

Other Features

Transmitter Operations

Service Mode is designed to disable the Remote Starting System. Service Mode must be

activated when having the vehicle serviced. When the system is in Service Mode the Keyless

Entry will still operate, if the start button is pressed the system will not start and give the

diagnostic for Service Mode by flashing the vehicles park lights 3 times. The system is easily

put in and out of Service Mode and should never be ignored for “Lack Of Convenience”

ULTRA

1.Press and release the # button, then within two seconds press and hold the

button for six seconds. After six second the park lights will turn “On” and the start

interval can be selected.

2. While the lights are “On” press the button corresponding to the desired start interval.

1 hour cycle or 0C Press LOCK button 1 Park Light Flash

2 hour cycle or -5C Press UNLOCK button 2 Park Light Flashes

3 hour cycle or -15C Press button 3 Park Light Flashes

4 hour cycle or -25C Press button 4 Park Light Flashes

3. The system will remote start for the programmed runtime at the selected start

interval for a maximum

24 hour time period then exit the Cold Start Mode.

TO CANCEL COLD START MODE

1. Press & release the # button, then press and hold the button for four seconds.

2. The System will respond with two flashes and two horn honks (optional).

Starting the vehicle with the key or remote starting will cancel Cold Start Mode.

Cold Start Mode Will Automatically turn off after 24hrs.

Never set the Cold Start Mode if the vehicle is park in a Attached or adjoined

Garage or Car Port.

Cold Start Mode

1 2 ... 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Ultra Start KE-6 Guía de instalación Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para La electrónica del vehículo de motor Ultra Start KE-6